12V 24V 2KW 3KW 5KW 8KW Air Diesel Monitor Switch Control Controller Board Motherboard Wire harness For Car TruVan

12V/24V3KW 5KW 8KW Air Diesel Parking Monitor SwitchControl ControllerBoard MotherboardFor CarTruVan Boat

Package Included:

Or4PCS SET 【1x Monitor SwitchController&1x Mother Board 1x e1x Wire harne】

Or3PCS SET 【1x Monitor SwitchController&1x Mother Board 1x e】

Or2PCS SET 【1x Monitor SwitchController&1x Mother Board】

Or 1x Monitor SwitchController

Or1x Mother Board

Specification:

Color:like the pictrue show

Voltage: 12V/24V

LCD Connectorpin: 3 PinsRound Plug

Fitment:

For 3KW 5KW 8KW Air Diesel Parking

ant Note:

1. There is a nsparent plastic protective film on the screenthatcan be removed before using.

2.If your motherboard and controller look the same as ours, all blaplugs. then you can buy a motherboard or a controller to rep your broken one. If your motherboard and controller are different from ours, you need to buy motherboard and controller together to rep your broken ones. Or it will not fit for your .

3. the e key only fit for this controller and motherboard, not fit for other type.

If you need to buy a set of controller, e key and motherboard, please choose 3PC SET. If only LCD Switch & e is selected, the motherboard is not included; if only Mother Board is selected, the controller and e key are not included.

Please don't e a wrong order! ! ! Please don't e a wrong order! ! ! Please don't e a wrong order! ! !

e Control To Codeinstruction:

In Power Off state, pre and hold Down on on the screen until HFR- is displayed on the screen to enter the e Control Pairing mode. Then pre On on on the e control to send out e control code.If paring is succeful, the machine will exit from e Control Pairing mode automatically. If paring fails, the machine will not enter power on state.If e control code is not received in time, the machine will exit from Paring mode.

The setting proce (pre and hold Up on to enter Setting mode)

1.Time Setting→Pre Up or Down on to adjust the s→set the value for Hour (24-hour system)and Minute in tun, and pre OK on to confirm and enter the next setting.

2.Auto Power-on Setting→Default setting is off and the screen shows loF. Pre Up on to activate and the screen shows loN,and then pre OK on to enter set the value for Hour and Minute in turn. Time is set as countdown, and the maximum is 99 minutes and 59 seconds.

3.Auto Power-offSetting->Default setting is off and the screen shows 2oF.Pre Up on to activate and the screen shows 2oN,and then pre OK on to enter set the value for Hour and Minute in turn. Time is set as countdown, and the maximum is 99 minutes and 59 seconds.

Enter Management Paword→Pre Up and Down on to adjust. When the correct number is displayed, pre OK on to enter the next di. When the 4-di paword is entered correctly, pre OK on to enter the next setting. If the number input is incorrect, it will return to the first di for re-entering. If there is no need to adjust other settings, pre Setting on to exit or wait 10 seconds to exit automatically.

4.Oil volume Setting→Pre Up or Down on to adjust the minimum oil volume and then pre OK on to confirm and enter the maximum oil volume settings Pre Up or Down on to adjust the maximum oil volume and then pre OK on to confirm and enter the next setting. 5.Fan Speed Setting→Pre Up or Down on to adjust the minimum fan speed and then pre OK on to confirm and enter the maximum fan speed settings Pre Up or Down on to adjust the maximum fan speed and then pre OK on to confirm and enter the next setting.

6.Working Voltage Setting→Mainboard working voltage can be adjusted only in power off state. Pre Up or Down on to switch between working voltage.For a 12v system, adjust until the screen shows U-12, and for 24v, adjust to U-24. Before starting the machine, e sure the oil ,engine and ignition plug can match each other so as to avoid damages.

7.Rotation Rate Signal Selection→The screen shows 5N-1.Pre Up and Down on to adjust Rotation Rate Signal. When the two s of the imr are the same, 5N-2 should be selected. When the two s of the imr are opposite or there's only one , 5N-1(default setting)should be selected.Ifa wrong is selected, the rotation rate can be double or half.

8.Ignition Plug Power Setting→The screen shows PF-5. Pre Up and Down on to adjust the (1=35W,2=40W,3=45W,4=80W,5=85W,and 6=90W). The default is 5. The default setting is recommended. It should be adjusted only when the new is verified.

9.Change Management Paword→Initial display is oF. Pre OK on to skip paword modification and save the modified . For modification, pre UP on and the screen shows oN, then pre OK. Pre Up and Down on to adjust the numbers and pre OK to skip to the next di.Pre OK to save the new paword and the new s and exit automatically.

Note:Time setting and Auto Power on/off'setting will take effect once it' s set. For the rest of the settings starting from Enter Management Paword, user must pre the OK on to confirm until all the rest of the settings are finished, so that the changes to the s can be saved.If the user exits before the last setting is confirmed, the changes will be lost and become invalid. Please cheand remember the new paword carefully to e sure you can enter the Settings next time.

If you have any question, please feel free to contact us.