A9 Car HUD Head Up Display 2 II Car-Styling Hud Display Overspeed Warning System Speed Windshield Voltage Alarm HUD

Overview:

HUD short for Head Up Display.It displays driving datas on the front windshield such as speed, rpm, consumption,water temperature,voltage;avoiding drivers become dangerous because of watching the instrument while driving.Drivers can read the driving information instantly,and can always keep the best state on the way with HUD.

HUD Main Functions&Features:

1.Available for cars with 2 and EU port(Car automatic diagnosis system) ,plug and play

2. Screen 5.5 inch HD display

3.Multi-color design es the screen more abundant and easier to read

4. Nano-technology to eliminate double reflections,more clear.

5. New function: Driving distance measurement

6.Rich Contents: speed, RPM, water temperature, voltage, instantaneous consumption,average consumption,driving distance measurement, voltage, shift reminders,fatigue driving reminders,low voltage alarm,high water temperature alarm,over speed alarm, engine failure alarm, eliminate the fault code,freely switch between kilometers&miles.

7. Auto power on/off: HUD start and off with vehicle started and shutdown, effective protection of the car battery;retaining the manual switch mode,more easy to control HUD.

8. Automatic and manual brightne adjustment mode,driving without glare

Display Function:

1.Decorative light

2.Engine RPM

3.Speed

4.Speed unit (KM/H, MPH)

5.Multi-functional area 1 : Engine RPM, voltage, Clock, single driving time(MIN), water temperature(℃/°F), 100 km acceleration time(a+)

6.Unit for multi-functional area 1

7.Multi-functional area 2: consumption, Trip distance

8.Unit for multi-functional area 2

9.Icon: setting, over speed alarm, fault code, light sensor,fatigue alarm, shifting reminding,water temperature alarm, low voltage alarm, mark

Warning

If do not use HUD for a long time, please pull out the cable

Troubleshooting

1.The screen without any display, and no power

Start the car engine; check if the cable line is tight; please pull out the cable more times to ensure; check if HUD power switch turns on. If still no display, please change another car to test, yze whether the car diagnostic interface is good, if it is not good, please repair it and try again.

2.When HUD power on, HUD only shows the car voltage and be automatic power off after a few seconds driving.

mode only available for cars with 2 and EU- agreement(European region: after 2003 years, Other region: after 2007 years)

HUD Products don’t support J and I protocol.

3.The device is stuck or stuck during driving

Check the interface if connected with other device,please remove other devices and do the factory reset (find menu 16).

4.Inaccurate Speed

(1)First check speed unit is correct or not, the speed unit including KM/H or MPH (refer to menu 11)

(2) When HUD is power on, vertical pre the setting on for 5 seconds to enter into the menu 1 and the shows 107,push left or right the setting on to increase or decrease the value according to the difference until it shows correct one. After adjustment, vertical pre in 5 seconds to save it.(Example:If the dashboard shows 100,and HUD shows 103,then change the HUD default value from 107 to 104)

5.Inaccurate consumption

The unit for consumption is L/100KM, HUD display is the single driving consumption, while car display is Integrated average driving consumption, so it is normal if there are difference.

HUD display three kinds of consumption

a. Idle mode: HUD display Instantaneous consumption per hour (L/H), it means HUD can figure out how much oil the car will consumed after start engine in one hour

b. Driving mode: HUD display Instantaneous consumption of 100KM

c. Finish driving: HUD display is average consumption of 100KM, when turn off the car, HUD will auto turn off in 10s

6.Stop-star cars,HUD shutdown after braking

Vertical pre in 5 seconds to enter into menu setting, short pre 14 times to menu 14, the default is 20, push left or right to change to 180, then power off time will be 3 minutes,then vertical pre in 5 seconds to save and exit,HUD will power off in 3 minutes.

7.HUD can not auto power off(RPM or Speed not at 0)

When HUD is power on,long pre in the on for 5 seconds to enter into menu,set to menu 13. Change the voltage from 0 to 13.2V or 13.5V. Once the adjustment finished,long pre in the setting on for 5 seconds to save and exit.

8.When HUD turn off, but restart

Find menu 13, adjust the default to 13.6-13.8 V

9.Clock calibration(this device doesn’t have battery,it needs to calibrate the clock once power off )

Long pre in the on for 5 seconds to enter into the menu,short pre in the on 15 times,to menu 15,it displays 12:00 and f,pull left to switch the hour and minute,pull right to adjust the dial number,once finished ,long pre in the on for 5 seconds to save and exit.