يستخدم هذا الموقع ملفات تعريف الارتباط. لمزيد من المعلومات حول كيفية استخدامنا لملفات تعريف الارتباط ، يمكنك قراءة إشعار الخصوصية وملفات تعريف الارتباط الخاص بنا. ملفات تعريف الارتباط وسياسة الخصوصية
الصفحة الرئيسيةمستلزمات السيارات والموتوسيكلاتادوات ومعداتأدوات قياسV5 V6 40mm 3D Touch Probe Edge Finder-Red Light
5,050.20 جنيه
9,847.89 جنيه49%
1 units left
مصاريف الشحن تبدأ من 1,515.06 جنيه الي 6 اكتوبر
وفر ١٠ جنيه على مصاريف الشحن عند الدفع مسبقا
0 out of 5
(لا يتوفر تقييم)عروض
التوصيل والارجاع
تم شحنه من الخارج
اختار العنوان
محطة الاستلام
مصاريف الشحن 1,515.06 جنيه
جاهز للاستلام يوم ٠٧ يوليو عند الطلب خلال18hrs 29mins
توصيل للمنزل
مصاريف الشحن 1,550.06 جنيه
يتم التوصيل يوم ٠٧ يوليو عند الطلب خلال 18hrs 29mins
سياسة الارجاع
يمكنك ارجاع اغلب المنتجات خلال 14-30 يوم من تاريخ الشراء، مع ضرورة الإبلاغ عن وجود اي عيب ظاهر في خلال 48 ساعة، للإستثناءات والشروط راجع سياسة الإرجاع من هنا.تفاصيل
الضمان
None
بيانات البائع
JG-Encantador
66%تقييم البائع
148 المتابعين
أداء البائع
معدل سرعه توصيل الطلب: ضعيف جدا
تقييم الجودة: ممتاز
تقييم العملاء: ممتاز
مواصفات المنتج
1.Clamp the probe on the machine spindle through the tool holder, and loosen it slightly.The two opposite fastening screws at the bottom can adjust the four symmetrical adjustment tops on the side.The ball head of the wire adjustment probe coincides with the center of the spindle.
2.There is no need to rotate the spindle when measuring the centering, and the centering measurement can make the probe rotate Turn 180° to make the measurement more accurate.
3.The probe supports measurement in three directions, X, Y, and Z, with reciprocating positioning accuracy less than equal 0.01, X Y deflection range 0-6°,Z direction telescopic range 1mm, exceeding Leaving the safe range will damage the probe and probe.
4.The probe has two built-in CR1616 3V lithium button batteries(not include),Loosen the fastening screw and adjusting top wire when it is insufficient, remove the top cover to replace it,Pay attention to the positive and negative poles of the battery when replacing, and re-adjust the probe center position after replacement Set.
5.The side head does not support the detection of insulating materials and insulated machine bed.
Name:The photoelectric 3D edge finder
The probe supports dust and a small amount of dripping and water resistance, do not drip for a long time
Dimensions: repeat positioning 0.01,Z direction stroke 1mm, XY swing about 6 degrees. Probe thread , ball head diameter 4mm, length 40mm. The detection of insulating materials and insulating spindles is not supported.
Power Suplly:two CR1616 3V lithium button batteries(without battery)
Type:Red Light
Colour:Gray
Material:aluminum alloy
Package Contents:
1 * 3d photoelectric edge finder
Only the above package content, other products are not included.
Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
2.There is no need to rotate the spindle when measuring the centering, and the centering measurement can make the probe rotate Turn 180° to make the measurement more accurate.
3.The probe supports measurement in three directions, X, Y, and Z, with reciprocating positioning accuracy less than equal 0.01, X Y deflection range 0-6°,Z direction telescopic range 1mm, exceeding Leaving the safe range will damage the probe and probe.
4.The probe has two built-in CR1616 3V lithium button batteries(not include),Loosen the fastening screw and adjusting top wire when it is insufficient, remove the top cover to replace it,Pay attention to the positive and negative poles of the battery when replacing, and re-adjust the probe center position after replacement Set.
5.The side head does not support the detection of insulating materials and insulated machine bed.
Name:The photoelectric 3D edge finder
The probe supports dust and a small amount of dripping and water resistance, do not drip for a long time
Dimensions: repeat positioning 0.01,Z direction stroke 1mm, XY swing about 6 degrees. Probe thread , ball head diameter 4mm, length 40mm. The detection of insulating materials and insulating spindles is not supported.
Power Suplly:two CR1616 3V lithium button batteries(without battery)
Type:Red Light
Colour:Gray
Material:aluminum alloy
Package Contents:
1 * 3d photoelectric edge finder
Only the above package content, other products are not included.
Note: Light reflection and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
المواصفات
المواصفات الرئيسية
- 3d Edge Finder
- 3D Touch Probe edge finder
- Three-dimensional edge finder
- Trigger 3D Edge Finder
- find the center desktop probe
محتويات العبوه
1 * 3d photoelectric edge finder
المواصفات
- SKU: GE810VP081EJ5NAFAMZ
- الموديل: Edge Finder
- بلد الصنع: China
- الحجم (طولx عرضx ارتفاع سم): 14x9x9
- اللون: Gray
- الخامه الرئيسية: aluminum alloy
آراء العملاء الموثقة
لم يتم تقييم المنتج بعد
V5 V6 40mm 3D Touch Probe Edge Finder-Red Light
5,050.20 جنيه
9,847.89 جنيه49%