12V 24V 2KW 3KW 5KW 8KW Air Diesel Parking LCD Monitor Switch e Control Board Motherboard For Car TruVan Boat

Note:

Since the logistics rejects all it with batteries, we can only remove the battery from the e control. After receiving the pack, please purchase the e control battery yours, we apologize for this! The battery specification is 3V on cell of CR2032/A27

Package Included:

Or 1x LCD Switch & e

Or 1x Mother Board

Or 1x Wire harne

Or 1x e

Or 3PCS SET【1x LCD Switch & e & 1x Mother Board 】

Or 5PCS SET【1x LCD Switch & e & 1x Mother Board 1xWire harne 1x Temp r】

Specification:

Color:like the pictrue show

e distance: Within 10m

Voltage: 12V /24V

LCD Connectorpin: 3 PinsTriangle Plug

e Control: 4 on

Battery: 1PC 27A12V, INCLUDED.

Fitment:

For 3KW 5KW 8KW Air Diesel Parking

ant Note:

1. There is a nsparent plastic protective film on the screenthatcan be removed before using.

2.If your motherboard and controller look the same as ours,  all blaplugs. then you can buy a motherboard or a controller to rep your broken one. If your motherboard and controller are different from ours, you need to buy motherboard and controller together to rep your broken ones. Or it will not fit for your .

3.The e key only fit for our controller and motherboard.

If you need to buy a set of controller, e key and motherboard, please choose 3PC SET. If only LCD Switch & e is selected, the motherboard is not included; if only Mother Board is selected, the controller and e key are not included.

Please don't e a wrong order! ! ! Please don't e a wrong order! ! ! Please don't e a wrong order! ! !

e Control To Code instruction:

1. Preing the up on to hold more than 3 seconds while in the off setting state.

2. Entering the e control to the code interface until displaying【HFR-】.

3. Preing theup onof thee to launch the e code.

4. Theis on after the e code disappear, or it won't turn on if the code failed.

5. The code will automatically exit when it is over time.

The setting proce (pre the setting key to enter the setting state)

1 Time setting:Pre the up or down key to adjust the s, set the hour (24-hour clock), minutes and other s in turn, pre the enter key to confirm the s, and enter the next item.

2 Timing power-on setting:default off, display 1oF pre the up key to turn on display 1oN, pre the enter key to enter, set the hour and minute in turn. Timing is a countdown mode, up to 99 hours and 59 minutes.

3 Timed shutdown setting:default off, display 2oF pre the up key to turn on display 2oN, pre the enter key to enter, set the hour and minute in turn. Timing is a countdown mode, up to 99 hours and 59 minutes.

Management paword input:Pre the up and down keys to adjust. When the correct value appears, pre the confirm key to enter the next di. After the 4-di paword is entered correctly, pre the confirm key to enter the next item. If the input is wrong, it will return to waiting for the first di to be entered. . There is no need to modify subsequent data, pre the SET on until exiting, or wait for 10 seconds to exit automatically.

4 oil volume setting:Pre the up or down key to modify the minimum oil volume. After reaching the required value, pre the confirm key to enter the maximum oil volume setting; pre the up or down key to modify the maximum oil volume. After reaching the required value , pre the enter key to enter the next item.

5 Fan speed setting:pre the up or down on to modify the minimum fan speed, after reaching the required value, pre the enter on to enter the maximum speed setting; pre the up or down on to modify the maximum fan speed, after reaching the required value, pre the enter on Go to the next item.

6 Working voltage setting:The working voltage of the motherboard can only be selected in the shutdown state. Pre the up or down key to switch and set the working voltage, adjust the 12V system to display U-12,

The 24V system is adjusted to show that U-24 has completed the release. Pay attention to chewhether the oil , motor and ignition plug of the machine are matched before starting the machine to avoid damage.

7 Speed signal selection:display 5N-1 Pre the up or down key to set the speed signal, select 5N-2 if the two s of the imr have the same polarity, and select 5N-1 when the polarity of the s is different or there is only one (default value)

If this is selected incorrectly, the speed will be doubled.

8 Ignition plug power selection:display PF-5 Pre the up or down on to modify the value (1=35W , 2=40W , 3=45W , 4=80W , 5=85W , 6=90W) The default value is 5. It is recommended to use the default value, or modify it after verification.

9 Management paword modification:Initially display the oF state, pre the confirm key to skip paword modification if no change is required, and save the above modified s. When modifying, pre the up key, after oN is displayed, pre confirm to enter the paword modification state, pre up to down key to adjust, after the 4-di paword is entered correctly, pre the confirm key to enter the next di, save the new paword and the adjusted setting s and then exit automatically .

Note:clotime, time of scheduled power-on and power-off, it will take effect immediately after setting, after setting all the s after the management and construction paword, you must pre OK until you exit after item 9, and then save the set s, if you exit midway, the previously adjusted data will be lost Miing is invalid. Please carefully cheeach newly entered paword and save it so that you can enter and change s next time.

If you have any question, please feel free to contact us.